Search the Community
Showing results for tags 'verify'.
Found 11 results
-
To make a long story short... I noticed that a buddy of mine has a set of scalloped tires on his Wing. He thought the $40 gauge that he had bought (gas station style chuck/gauge combo) would be accurate. It showed that he had 40lbs in the front. I checked it with my new Accutire digital gauge and it showed 32lbs. I understand Accutire brand are supposed to be accurate but I'm going to verify mine at work tomorrow since we have a calibrated gauge that is only used to verify other gauges.
-
I was sold these as going on a MKII 1st Gen bike and since I have a MKI as well I can verify it goes to neither... any help out there with finding their proper use? http://www.bergall.org/temp/venture/floorboards/mc1.jpg http://www.bergall.org/temp/venture/floorboards/mc1a.jpg http://www.bergall.org/temp/venture/floorboards/mc2.jpg
-
Not sure where to put this question on the forum sorry I am wondering if the 2006 TSD I am looking at is a Midnight version have only pictures to go by and don't know what questioins to ask to verify if it is a midnight..all I know is that it is a black 2006 and looking at the history section appears that would mean it is a midnight model...??? Any suggestions on how to pin down the ident.??
-
I have a set of fishtail pipes for the RSV that I'm trying to ID before I sell. No identifying marks on it that I have found. RSV mounting tab for under the bags. No seams, can't remove the baffles. I'm thinking Samson, but don't know how to verify. Any thoughts? I'll get some photos posted later this afternoon. Iz
-
I'm looking for anybody that has carb syn gauges that live in Cleveland Oh that I could use to verify my own gauges. Thanks In advance. PM me -
The Dunlop web page shows an Elite 3 front tire is now available for a MK1; Elite 3 MR90-18H part# 4079-84 Can anyone verify this is correct before I order one from MotorCycle SuperStore?
-
Got 83VR non running, lot of work later runs great but tach reads low, and slow to respond to throttle changes. Dash was FULL of ants, disassembled, and flushed ants out with water, then dried with aircompressor. Any way to verify tach signal at rear of dash correct? Volts?, Ohms? Think this signal is pulsing ground/vs 12v behind coil#2 @2xRPM?, May put o-scope on just to see what it reads. Haven't used my scope in long time-hope it still works. Suspect tach gears/springs may have light corrosion needs lube (pull dash again:(), but would like to verify everything else first.
-
Over the winter I had reported that what I thought was a dealer installed I-basket (last July) actually was a G-basket. I complained to the dealer and eventually got an I-basket which eliminated almost all of the whine. A few of you commented that you were thinking about pulling your clutch basket to verify whether or not you do or don't have an I-basket (when you felt that you do). Just wondering if anyone has followed through and what was discovered?
-
please verify crash guard
mountainhorsega posted a topic in Royal Star Venture Tech Talk ('99 - '13)
Can one of you gurus here verify? I am almost certain the crash guards are the same on the tour deluxe as the venture. Can anyone verify that? -
Please help my Granddaughter with a vote for the 106.1 FM kissable babies. Follow the link below and skroll down to (EMILEE) pick the picture and enter e-mail address at the bottom of the page,check your E-mail and then verify. They all look kissable so you may vote for more then one I think. You may also vote once everyday during the contest. Here is the link : http://www.1061kissfm.com/pages/contests/baby/vote_group_11.html Thanks so much.
-
I'm suspecting that the newer V-Maxes probably use a throttle position sensor on the carburetors, and I figure the older ones didn't. Can anyone verify whether the newer ones really do or not and what year they started being used?
.thumb.JPG.bfcefdc0995aabc77d6b4e8cf9125c91.JPG)
