Search the Community
Showing results for tags 'portion'.
-
Well I guess since I decided to keep my 99, I might as well go for broke! This year all I planned to do was put on a new ignition switch, and 4 new intake manifolds. BUT....as most of us Venture riders know, it never stops with just this or just that. So I have decided to buy a head set, a gps unit, the ignition switch, 4 intake manifolds and get this.....A TRAILER! But....not just any trailer....a custom built to my specs trailer. All aluminum framework, aluminum diamond plate lids, aluminum flatstock walls d/a'ed for a nice look. The trailer is 4' long by 3' wide by 3' deep for the storage portion. But in front of the storage portion will be a 1' by 3' cooler with a lid that opens seperate from the back. It will have double walls with insulation in between them and a built in drain on the bottom. I'm STOKED! the plans are being drawn up on a computer program today, and my uncle will be starting on the production before spring. He works for a company that customizes fire trucks, so he likes to do some little projects for fun, and we have been kicking around this idea for about a year. I'll be sure to put up some pics when we get it underway! Will look very similar to the top two pics in this page http://images.google.com/imgres?imgurl=http://allstartrailers.com/images/mct_and_mctxl_motorcycle_trailers2.jpg&imgrefurl=http://allstartrailers.com/Motorcycle_Trailers.html&usg=__dIsVkBlOWrvx9VwmjYusculAzO4=&h=1944&w=2592&sz=1317&hl=en&start=20&um=1&tbnid=VmypOopCxBGwBM:&tbnh=113&tbnw=150&prev=/images%3Fq%3Dmotorcycle%2Btrailers%26hl%3Den%26sa%3DN%26um%3D1 YEE HA!!! Big Mike
-
I have a 1300 tha I purchased last month with 11,500 miles. As I have begun putting on miles and getting used to her an oil leak has developed. At first I did not see anything, but thought I smelled burnt oil. Then a couple drops of oil on the garage floor appeared, and now it's 4-5 drops. Today I got underneath and took a look around. The left side of the exhaust collector has oil on it. There is also oil on the lower portion of the driveshaft cover. There is no oil i could see above the driveshaft. So here is my question. What are the likely locations for oil leakage? Is there a sensor I cannot see? (fingers crossed) Or is it a seal for the output shaft?
- 10 replies
-
- driveshaft
- drops
-
(and 3 more)
Tagged with:
-
Other than being the famous last words of the Hindenburg pilot, what does the small slider switch on the dash, to the right of the handle bars at the vertical portion of the dash panel next to the "grate" do? http://i433.photobucket.com/albums/qq60/ivanstein/IMAGE_018.jpg?t=1227930215
-
Use caution when ordering these extra wide clamps from Choppercycle. If you look at the pictures (use Link) you will see a raised rib portion on the inside of the clamp. The raised portion of the clamp makes the clamp too small to allow the muffler to fit unless you spread the clamp open. If you spread the clamp open it will fit over the muffler but because of the extra thickness the rib presents it wil not tighten down properly on the exhaust pipe. If you want to use these clamps you will need to grind this raised portion of the clamp down. This took me about 40 min each and I went through 6 dremal sanding dics. I didn't notice this when I ordered the clamps. They do look good however. http://www.chopperscycle.com/page/VTS/PROD/42-264/24032