Search the Community
Showing results for tags 'measurement'.
Found 10 results
-
Could some one please give me the measurements for a Diamond R Receiver ? I need some measurements from you kind folks pleaseeeeee. ? Thank you in advance..... [ATTACH]67619[/ATTACH] [ATTACH]67618[/ATTACH] A. Measurement from front to rear, measuring on the top side. B. Thickness of the receiver bar. C. Measurement from top to bottom of the receiver on the front side, not including the thickness. D. Measurement from top to the center of the pin hole. E. Pin hole size ? F. How wide is the receiver from one side to the other ? James
-
I have not had good luck searching the 1st gen tech area on setting the carbs on my '86. I have done them, in the past, like the manual states. Frankly this is a PITA as you have to assemble and pull apart the carbs till the tube fill line is where it states it should be on the center. The G2's are WAY easier to set as there is a measurement where to set them. My question is to any of the 1st genners, have any of you come up with a measurement that can be used to set the floats, like on a G2? If I can't get a response in a day or so I'll be doing it the manual way, but if there is an easier way to set these things....I'm all ears!
-
Hello. I still am trying to get a loan on a RSV so yes...I still dont have one. I need to know what the distance is between the idiot light panels next to the cassette door. I am thinking of modifying the cassette hole and need a measurement from the right edge of the left window to the left edge of the right window. i am thinking of installing a FUSION MS-RA200 marine radio in the cassette hole and eliminating all the Clarion electronics. Please let me know if you can. Thank you.
-
Does anyone have an MKII driveshaft that they could get me a length measurement from ? I am having an issue with my MKI shaft and the FJR rear end Gary -
NO SMART REMARKS!!!!! I don't have the little plastic dip stick for the rearend oil. Can somebody at least give me a measurement off of there's so I can make my own? I would very much appreciate it.
-
I know that the service manual states on page 8-24 that the stator coil resistance ought to be between 0.279 and 0.341 ohms. Has anyone actually taken this measurement (excluding the run to pin 4 - since that seems to be a typo)? If so, what did you end up with? I am currently trying to troubleshoot my scoot and have already done the voltage check at the battery (which the scoot clearly passed). I have taken this measurement, but the resolution of the meter that I used is only 0.1 ohms, and I do not know for sure what the accuracy of the meter is nor what the TRUE range of this meter is... I have a better one at my office, which I will pick up when I go in next time to redo this measurement. The goal here is to verify that the stator is good/not good before I install and possibly ruin a new radio and/or not waste the money and time on a new stator if it is not necessary. Thanks in advance!
-
Hi gang, would somebody go out to there garage ? *lol* I need a measurement from the back of the rear passenger seat to were it meets to the back of the speaker pods or trunk pod. PHOTO would be OK too! Thanks, Jeff
-
Here's a pic of the '06 I'm looking at buying. I'll need to transport it home in the back of my Dakota truck. Can anyone pls provide a measurement from point A to point B for me? Need to figure out if it will fit in the box or straddle the tailgate or what. Thanks
-
I am away from home and need to get some measurements on the seats on a 2nd Gen pillow top (had to leave the bike behind this time). Need the measurement from front to rear on both seats and the width on both as well. Thanks for any help you can give.
-
Hey Folks, I have my '86 down and apart and decided since it's this far down I would take the carbs off and check the float levels to be sure they were in specs. This is where my problem lies, the manual doesn't give a measurement at where the float should be set at statically, it shows how you can check if they are high from the outside and together, but not a measurement internally. Does anyone know the measurment that they should be set at and where the measurment is taken from. I am glad I did this as someone has been into these carbs before and I had a screw fall out that wasn't installed properly. Any help would be greatly appreciated.
.thumb.jpg.176b2ebbe9863175975d94710375c414.jpg)
