Jump to content

camarojunkie85

Expired Membership
 View Profile  See their activity

  • Posts

    22

  • Joined

  • Last visited

Reputation

10 Good

Personal Information

  • Name
    Kevin Reed

location

  • Location
    Highland Heights Ky, United States

Converted

  • City
    Highland Heights Ky

Converted

  • Home Country
    United States

Converted

  • Bike Year and Model
    1983 Yamaha Venture
  1. camarojunkie85
    I do now yes. Im still getting backfire when revving up but that may be unburnt fuel from all the cranking checking for spark. But it revs great now, I was surprised at how fast it revved next to vmax. Can't wait to fervor on the road tomorrow, I pulled this beaute out of a yard its been sitting in for 9 yrs.
  2. camarojunkie85
    Haha, your welcome. Not sure if that is the switch that is bad or what!
  3. camarojunkie85
    Well probably something I should have checked, but the kickstand switch must have went out. It didn't work before and I could start in gear.. but now it seams as if it may have grounded out or something. I clipped the black/white wire from the tci harness and fired right up. Man how stupid can I be!!!
  4. camarojunkie85
    Bkuhr just got your tci and o still have no spark. Problems elsewhere I assume! This is nuts. Im not sire what the problem is but battery was completely dead to so I jumped it doing this, could something have fried that's not letting it get power to tci or something from battery???
  5. camarojunkie85
    Lol, id love to, but man I've got enough lol. Got a couple 80s models I gotta start selling. But thanks.
  6. camarojunkie85
    Would u guys know if a vmax tci would work in the venture for suree, like 85-90 vmax on my 83 venture. I think one would be easier to come by, plus I have vboost im waiting to put on and the curves might be closer to vmax than venture. Also I think some of the connector tabs separated from the boards when I was tugging on it, may have destroyed my venture board.
  7. camarojunkie85
    Oj well the red w/ white striped wire had 12v sitting and cranking to. So I have power ro the tci. Any other thoughts. I don't have anyone near me to try theirs!
  8. camarojunkie85
    I will try that! Should i worry about resistors that are swelled up and a little rusty looking?? Cause it did work before
  9. camarojunkie85
    Well it does get hot from just cranking, ill try that. I have some resistors that are swelled up maybe from water? Could that be a problem??
  10. camarojunkie85
    Out if curiousity can I use my multimeter on the board its self for tests, thus would eliminate alot of my struggling.
  11. camarojunkie85
    I didn't bake it, I just cleaned out holes and solders in new ones. Yes I do know they go one way, that was the first thing I double checked. It just seems weird that I have no spark. I havee soldered before, so I know I didn't goof there.
  12. camarojunkie85
    Ok kill switch works, not a single spark from amy of 4 coils.
  13. camarojunkie85
    Yacht switch I meant kill switch making tach jump** I apologize this was all from my phone. Yes i replaced all diodes like I said was it 6 or 8, don't remember. And at the r/w wire for kill switch, I ground probe and use that r/w wire as hot side for probe and I should be able to flip switch and get 12v on and off correct?
  14. camarojunkie85
    Well I soldered in all 8 or 6 diodes however many there were. But im not sure of my kill switch is bad or what now but I have no spark at all. If I push the kill switch it makes the yacht switch jump a bit was that normal? But do you have any other tests I can try. I wasn't sure if maybe I lost ground from pulling coils also or what!. But now im furious lol.
  15. camarojunkie85
    Ugh, I got the tci box off, and it started dripping water. So im going for that. Being the problem lol. Relocation *definitely*
×
×
  • Create New...