Jump to content

Yammer Dan

Supporting Member
 View Profile  See their activity

  • Posts

    23,013

  • Joined

  • Last visited

 Content Type 

Everything posted by Yammer Dan

  1. Yammer Dan
    Want to sell that Burrito Case??
  2. Yammer Dan
    Good looking one I look at them every time I come across them but haven't been lucky yet!
  3. Yammer Dan
    It does make you think. A GOOD rubber tube that you could depend on and a valve to control flow??? You never know.. I think on top of the pan to heat the foam sounds possible. The valve would be important as to how much flow and being able to shut down if bike overheated!!
  4. Yammer Dan
    First thought is you wouldn't be able to control heat. Might get a little warm down there.
  5. Yammer Dan
    I think it is the MAF but it runs great without it. I think I only need the sensor and not the entire unit as they are trying to sell me. Drove it all week and it ran great.
  6. Yammer Dan
    Will try to remember this one!! I stay away from most Stealers because of Domm's in Charleston WV.
  7. Yammer Dan
    Put that new battery in storage someway? Maybe with a float charger? Or did you use old one for exchange?? Lessons like this we remember.
  8. Yammer Dan
    Slim and None. If you hear from him it will surprise me.
  9. Yammer Dan
    SEA-FOAM. Might be time for a set of plugs. These bikes don't like to sit. Goose's approach to using Sea-Foam is a good one but just drain it to less than 1/2 tank put in full can of Sea-Foam ride using throttle at all different positions for 50-75 miles and fill with fresh gas. Problems not gone then you have a bad plug.
  10. Yammer Dan
    Shouldn't have changed it that much unless you had air in it. Did you open bleeder when you pushed the pads back?
  11. Yammer Dan
    Good News Clay. Coming home is always the best part!!
  12. Yammer Dan
    Camera?? Still a dream. I have a Kodak easy share but haven't figured it out yet.
  13. Yammer Dan
    I think you got it. Thats what I thought til they tried to sell me whole thing. Whole unit is Throttle Body with Mass Air Flow Sensor connected to side of it. One for sale on E-Bay he called it Mass Air Flow Sensor and showed throttle body. You could see wires coming from it but he didn't show side of it where what I thought was sensor was Am I making sense now ?? I'm getting confused..
  14. Yammer Dan
    She was glad to see Frost!! She don't have to cut grass anymore!!
  15. Yammer Dan
    I'd wear mine!!! It might hide part of that view DOWN!!
  16. Yammer Dan
    Keeps them looking over their shoulders!!!
  17. Yammer Dan
    Frost this morning. Warden went out and fired up ride so I wouldn't have to get in it cold!! After she laid out my clothes put breakfast on the table. And took my lunch to the car.
  18. Yammer Dan
    CONGRATS!! Creek Rising won't work with that 4-Wheel drive!!
  19. Yammer Dan
    I was named Yammer Dan by the Prez of a Outlaw bike Club in 1975. Guess I'm stuck with it. Lot of Hardley riders know it.
  20. Yammer Dan
    They been practicing on some of our West Virginia roads??
  21. Yammer Dan
    OK! OK! You forced me.. I'LL POST!! Is that ENOUGH??? Redneck they said Lurkers not LUNKERS!!
  22. Yammer Dan
    Ran it about 100 miles today. Ran better than it has in long time. Not really getting what is wrong. If you unplug it it runs great. Which means it is opening up to let air in. Is the little black box what is messed up and it is not telling it when to open?
  23. Yammer Dan
    OK Fib now I'm confused (again) This shows the intake valve? itself. I thought the sensor was the little box on the side of it. When I just unplug the electrical box on the side of the Air Mass Flow valve? It runs fine. Plug it up and won't hardly run at all. Not sure what I need now. Are they trying to sell me this entire unit? Do I need it or just the switch?
  24. Yammer Dan
    So if my gas milage don't suffer too much just leave it unpluged will cause no harm??
  25. Yammer Dan
    I would have already gotten stupid!!
×
×
  • Create New...