dingy

Pin outs shown in attached picture of where traces go to on board for connectors pins. You probably don't need this since you cut box open. Handy to have where pin ended up in case a trace was damaged when soldering pins. Picture of board shows replaced diodes. They don't have to be right against board. It is easier to leave them higher up, then a heat sink, like an alligator clip can be attached to longer leg. Gary

Attached are some pictures of one I cut open. Very center of board, there is a component I cut with band saw. Also a picture of section I cut out. This is a very bad one inside. It wasn't working. Gary

Collector on Ebay that ends tonight. http://www.ebay.com/itm/1983-1993-Yamaha-XVZ1200-1300-Venture-Center-Chamber-Rear-Headers-NICE-4085-/310966180935?pt=Motorcycles_Parts_Accessories&hash=item4867075c47 Gary

Couple of pictures of scrape on it, Looks like bike fell over, marks aren't nearly bad enough to have been a rolling crash. Gary

I have a fairly good right hand one. Minor scrape on outboard edge. Gary

They are 45mm dia. I don't know dia, but I can check tonight when I get home, if I remember! Gary

Remember how much fun it was pulling t-stat, it will be easier to do the 2nd time when you need to fix o-ring. Gary

Does the RSV diagnostic light function with the Dyna 3000 unit? Gary

Both, neither maybe ?? Gary

Attached are a couple of stills from the motor rebuild video showing a motor stand. Threaded rod is 3/4" per video. Gary

The clown shifter has met a very early demise on Sylvester (aka Hybrid). When I put the floorboards on frame, I thought there has to be a better option. I got a new stock 1st gen shifter today from ebay for an extremely good price. It can be changed in 10 minutes. Bushing size is the same, adjustment screw assembly attaches with no changes needed. 3 sets of pictures, one set of 2nd gen shifter, one set of 1st gen shifter and one set with them somewhat side by side. Gary

Yes. Gary

Part #'s that are in 1st post will work on 83-93 Ventures & 85-07 VMaxs Gary

Almost missed it. Big Six Zero. Hope you are well. Gary

Looks like it is, guess though. Be neat to have if you have tester. Gary

Did you find manual for tester? I would like to get a copy of it !! Gary

All I saw in service manual dealt with spark plug gap testing. Gary

Yes Gary

That I do not know, mufflers were a blind stab at what might work, rest is no chance. Didn't get the stock exhaust when I got my RSV Hybrid parts collection. Gary

They are completely different pipes, 1st gen to 2nd gen. Not a chance of making anything work other than mufflers, maybe. Gary

Bob, Anybody else on list better to ship you ?? 86er: $45 Item #1 1st Gen instrument cluster, very nice condition Ground-Hugger: $50 Item #8 1st gen pouches. In general nice shape, Adventurer 08: $80 Item #9 4 brush starter JohnT: $40 Item #14 K&N air filter JohnT: $30 Item #15 Spin on oil filter adapter with cooling ports. DragonSlayer : $60 Item #21 New, unopened Gear Pro camera. Ragtop69GS: $20 Item #23 New Motion Pro fork level gauge. Ragtop69GS: $20Item #25 Motion Pro 41mm seal driver Stickhandle2: $30 Item #26 Yamaha Steering head adjusting wrench

I will get pouches in mail tonight. It takes about 2 weeks for delivery to Canada. Gary

I think I end up using McMaster p/n 6659K13 in stator housing. Stock setup is with 2 short sleeve bearings pressed in from each side though. I went with one longer bearing pressed in from outside. These are 15mm OD x 12mm ID x 20mm long. Bearings are about $1 apiece. The 15mm drill I got was McMaster p/n 3091A33, reduced shank so it would fit in a 1/2" drill chuck, $23. Stock bearings are 14mm OD, which I didn't find a replacement for. I also put same bearing as above in shift pedal on RSV Hybrid. It reduced play in assembly quite a bit. Screen capture of parts I ordered from McMaster attached, didn't use all of them. Gary

Paypal ID is in red text below. Payment for auction items I listed will go to Lewis Cramer, DragonRider. I will send shipping amount, that can be paid to me. I will need shipping address PM'd to me. Gary Here is my paypal addy for those who won the auctions that Dingy was doing for St. Jude. Please include a notation that this payment is for Dingy's auctions and please mark as a gift or donation so fees wont be taken out. partin_guy@yahoo.com there is an underscore between( partin_guy) Thanks for supporting St. Jude. Lewis

I sent a PM to Dragonrider about accepting payments for my auction items as well. Gary