Leaderboard

Leave it, it's working just fine.

I personally like paying the $12. Keeps the riffraff out. (Somehow I made the cut 🤫). What I don’t see here that I see in just about every free car forum out there is endless bashing of ideas or questions. I don’t have to sift through 50 -100 posts looking for the three that may help me. I don’t see discouragement. I see genuine honest people with similar interests having a good time.

If you can repair the stuff that it will need, buy it. If you have to pay someone else to repair it, buy a newer bike. One member bought a cheap not so good 83 and had about $5,000 invested by the time it was finished because he paid someone else to repair what it needed. He seemed happy with the end result. And most shops won't work on a bike this old. Another member bought a clapped out 83 and did a frame up repair himself and it looked great afterwards. They are fast, fun bikes after you get them roadworthy.

I can't tell which group it was but doubt it was the VentureRiders page.

Everybody knows all the cool kids hang out here anyway.

Which one? If I’m on it I won’t be anymore.

Submitted by bbstacker: ok, actually it was easier than I thought it would be, if you just jack up the front of the bike so the wheel is off the ground it is easier. first the front half of the fairing comes off, you have the small chrome strip on top with 2 screws, then you have 7 more for the front half of the fairing, 6 on the back and 1 under the headlight, then the windshield, 8 small screws holding that on. Once you have the front half of the fairing off, you may have to unplug just a few of the cables, I did the bigger round ones, because once you take out 2 nuts that hidden behind all the cables, once you get those off, you can pull the other half of the fairing away from the triple tree. Now you need to make sure you have a good pad laying across your tank for your handle bars to rest on. There 2 allen bolts on the front side of the triple that hold the bracket on for the fairing, take off the handle bars, then the big nut and washer holding the top of the triple tree. Just loosen the 4 bolts (2 on each side)used to clap the top part of the triple tree to the forks, take the top part off, you then can slide the 2 top fork covers off, there will be a big washer and rubber gasket inside. Before you loosen the 4 (2 on each side) bolts on the bottom part of the triple tree, make sure you mark where the forks are set, so you can measure up 1 inch from that mark down to top side of the bottom of the triple tree,once all the bolts are loose the forks will probably slide on you. All you have to do is either slide the forks up or down to get your 1 inch, lock one side then measure and lock the other side, put the covers back on making sure you put the washer and rubber gasket in correctly, put the top of the triple tree back on,then the washer and nut, tighten that then reinstall the 2 allen bolts, everything is just in reverse putting it back together. All this may sound complicated but trust me it is not, it's about a two hour job, that is unless you get it back together and forget to put the two forks covers back on like I did and have to take it apart again. I didn't take any pictures, I should have. As far as the kickstand, no problem, bike still leans on it the same just shorter, I will say the bike comes up on center way easier also. If you find you don't like it it's easy to change it back, myself, no way will I change it back. I have 40 lbs of air in the shock, I ride 2up and pull a trailer, (one that I made)and no the pipes don't drag. Hope this explains it well enough, if not send me an email and I'll try and do a better job. I would find a hard time believing you won't like the new ride. Good luck, any questions be sure to email me, I've been riding for over 40 years and do most of my own maintenance and all of my own mods. Hey I know this isn't for everyone, but that's what choices are all about. Take care and ride safe. Picture courtesy of Rosebud.

No warning or anything....just, "Get Out"