Looking for Larry

[ReinyRooster]

Yo!! Carbon One.......tried to send you a message but it wouldn't go through. Looking for one of your wired mounts for a Wolo horn.

Rooster

[Squidley]

Unfortunately I don't think Larry is making any of his products any longer Rooster. 

[sleepy2]

With Phantom Wife being so thrifty  ???    I just cut and  shaped my own to fit contour around bolt below where oil is put in .

[ReinyRooster]

OK, I'm guessing I will have to Mcgiver something......

[XV1100SE]

I do have one....

[ReinyRooster]

...to sell?

[Carbon_One]

Reiny I do have a couple brackets that have been started but need finishing Polishing mostly. If Don has one to offer you fine if not send me a message.

Squidley I do offer some of my products but don't advertise then so only build what is asked for. Being the 2nd gens are no longer made by Mom Yamaha demand is quite low so it don't make sense to tie up material and storage space.

[Squidley]

13 hours ago, Carbon_One said:

Squidley I do offer some of my products but don't advertise then so only build what is asked for. Being the 2nd gens are no longer made by Mom Yamaha demand is quite low so it don't make sense to tie up material and storage space.

It's good to hear that you're still making some of your items. I'll keep that in mind when I hear of folks needing anything you make. Hoping you and Joyce are doing well my friend 👍

[RDawson]

@Carbon_One are you still making the jack adapters? I’m making one for a local this week but have no interest in selling them. I’ll keep sending people your way. 

[videoarizona]

Larry, I'm wondering if the adapter I bought from you can be adapted to take the stand? Guess I should have ordered the stand too....but $$ was tight at the time.

[XV1100SE]

20 hours ago, Carbon_One said:

Reiny I do have a couple brackets that have been started but need finishing Polishing mostly. If Don has one to offer you fine if not send me a message.

Squidley I do offer some of my products but don't advertise then so only build what is asked for. Being the 2nd gens are no longer made by Mom Yamaha demand is quite low so it don't make sense to tie up material and storage space.

@Carbon_OneHow much were you selling the horn brackets for before?

[Carbon_One]

On 9/21/2021 at 2:03 PM, videoarizona said:

Larry, I'm wondering if the adapter I bought from you can be adapted to take the stand? Guess I should have ordered the stand too....but $$ was tight at the time.

Can't use a center stand with my jack adapter due to both using the frame tabs below the engine. You would need to remove the center stand 1st , attach the adapter then reinstall the center stand when done. 

[Carbon_One]

On 9/21/2021 at 3:37 PM, XV1100SE said:

@Carbon_OneHow much were you selling the horn brackets for before?

$30 including shipping to either USA or Canada

[videoarizona]

5 hours ago, Carbon_One said:

Can't use a center stand with my jack adapter due to both using the frame tabs below the engine. You would need to remove the center stand 1st , attach the adapter then reinstall the center stand when done. 

Ooops... Sorry, Larry. Guess I got the terminology wrong. What I meant was can I retrofit the legs you make for the lift adapter? I didn't buy them initially. Or is that adapter built differently than the adapter I bought?

[Carbon_One]

Ok if you bought my lift adapter without legs then you could add the legs at a later date. You'll need to weld on the receiver part to the main frame. If you need further info send me a PM for converting what you now have. If you bought the adapter you now have from off e-bay I may not be able to convert your adapter due to different size & measurements.

[videoarizona]

Hi Larry,

The site says you can't receive PM's.....I tried sending one to you. Here's my message.

"Hi Larry,

I bought the adapter from you...so the legs should fit fine. Just need to know cost and instructions on how to attach the legs....

Thanks!

david"   

 

 

[luvmy40]

Larry, 

Any chance I could order one of your RSV lift adapters with the legs for my '06 RSV?

Rich Schaefer

(330)651-2779

[philzy127]

I would love one for my 2006 RSTD also, please.
 

[Carbon_One]

On 9/26/2021 at 8:56 PM, luvmy40 said:

Larry, 

Any chance I could order one of your RSV lift adapters with the legs for my '06 RSV?

Rich Schaefer

(330)651-2779

Send me an e-mail at ljskeels@att.net

[Carbon_One]

On 9/28/2021 at 3:34 PM, philzy127 said:

I would love one for my 2006 RSTD also, please.
 

Send me an e-mail at ljskeels@att.net

[Carbon_One]

On 9/23/2021 at 10:29 PM, videoarizona said:

Hi Larry,

The site says you can't receive PM's.....I tried sending one to you. Here's my message.

"Hi Larry,

I bought the adapter from you...so the legs should fit fine. Just need to know cost and instructions on how to attach the legs....

Thanks!

david"   Send me an e-mail at ljskeels@att.net

 

 

[luvmy40]

On 10/6/2021 at 4:30 PM, Carbon_One said:

Send me an e-mail at ljskeels@att.net

Emails sent

[Handyairplane8]

is it possible to get a picture of the adapter?