Yammer Dan Posted October 19, 2013 Share #1 Posted October 19, 2013 Best title I could think of. While cleaning I found some rust on chrome that after cleaning rust away there is bare metal. What is best to put on these spots when putting back togather. They are going to be hidden for the most part. To protect them and keep rust from forming? Some of them would be in sight. Clean these to as bright a shine as you can get and apply wax and just try to pay attention to them??Or is there a clear coat that would keep rust away longer? :think: Link to comment Share on other sites More sharing options...
kevin-vic-b.c. Posted October 19, 2013 Share #2 Posted October 19, 2013 If they are small spots I would find some high heat or rust paint, depending on where they are, in silver and take a small art paint brush and dab them with some paint. Adjust brush size and paint quantity to cover well. I know there is rust stop products on the market but most of them leave Black in place of the rust. You can do that then paint over them in Silver also. Link to comment Share on other sites More sharing options...
Condor Posted October 19, 2013 Share #3 Posted October 19, 2013 I'd use a hard Carnuba wax on the area. As long as you can't see it, lay it on thick. Link to comment Share on other sites More sharing options...
friesman Posted October 19, 2013 Share #4 Posted October 19, 2013 On my vehicles and when I store the bike I use rust check on exposed metal and joints that wear. It just sprays on and leaves a light film over the area. In spring I clean the bike normally and most of the film comes off, but I think it still leave a bit of an invisible coating behind. On the 4 wheelers ive sprayed behind the wheels and around the wheelwells and even inserted the long stray inside the doors where moisture and condensation accumulate. Ive never had a vehicle get a rust through situation since Ive started using it. BTW I use the red can Rust inhibitor Brian http://www.rustcheck.com/ Link to comment Share on other sites More sharing options...
bongobobny Posted October 19, 2013 Share #5 Posted October 19, 2013 Dab 'o paint then metal polish after it dries... Link to comment Share on other sites More sharing options...
M61A1MECH Posted October 19, 2013 Share #6 Posted October 19, 2013 I think you would do well with some good clear coat from a rattle can. I picked up a Harley tail light assembly from a swap meet a couple years back. Had some pretty ugly surface rust on it, I worked it over with dremel with a brass brush wheel and some polishing compound, looked brand new when I was done, gave it a coat of clear from a rattle can and she still looks great. One thing, if you use the brass or stainless steel wire brushes from Dremel, make sure you wear good eye protection, because after a while those wires start to shed and they will take out an eye in a heart beat, and they are not magnetic so if you get one in the eye they will not be able to extract it using a magnet like they do for steel bits that end up in people's eyes. Link to comment Share on other sites More sharing options...
Yammer Dan Posted October 20, 2013 Author Share #7 Posted October 20, 2013 I have the Dremel out. The POR 15 looks like it might be worth it. I couldn't find the silver in a starter kit. Silver would probally work on the crome back in some of the hard to get to places. As Bubber said pricey but would be worth it if it lasted a while. Link to comment Share on other sites More sharing options...
MidlifeVenture Posted October 20, 2013 Share #8 Posted October 20, 2013 Make sure to but a baggie between the lid and can when resealing it or the lid will never come off a second time. Paint out of a separate tray Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now