kkent66 Posted April 5, 2013 #1 Posted April 5, 2013 I have a 2006 RSV with 54k miles. March of 2012 I upgrade my clutch spring with a PCW heay duty clutch spring. I did not upgarde my friction plates as the guy at PCW said those should be good for 75k miles. Here is a list of all mait I have done the past few months; Flushed cooling system Replaced Spark Plugs Changed oil & filter Changed final gear oil New Rear brak pads New Front brake pads Flused front and rear brakes with might vac Flused clutch with might vac Installed HID ligt Istalled a tune trapper antenna installed a power amp and new polk speakers - front and rear Sync carbs with my new morgan carb tune Installed an iphone charger directly wired to battery with relay and on/off switch My bike is running better than ever but I still get a little bit of slippage when I roll hard on the throttle. I am wondering if I need to replace friction plates?? No problems shifting and if I dont "floor" the accelerator no slipage. Any thoughts would be greatly appreciated.
TheKid Posted April 5, 2013 #2 Posted April 5, 2013 What kind of Oil are you using? The different Oils can cause slippage as well. Did you check your friction plates when changing the spring? Did you do the upgrade to the last plate to make it a whole friction instead of a half?
WildBill1 Posted April 5, 2013 #3 Posted April 5, 2013 Clutch slipping is often the result of using improper oil in these engines. They need m/c oil not automotive. Don't know if you were using auto oil with friction modifiers or not, just saying. Once the plates have slipped very much its best to just change them out. Bill,
SilvrT Posted April 5, 2013 #4 Posted April 5, 2013 If you just replaced the spring and the clutch was slipping before that, then you should have either ... a) removed all the plates and friction discs and scuffed them with emery b) replaced the friction discs while at same time scuffed the plates. Actually, this should have been done regardless if it was or wasn't slipping beforehand.
Flyinfool Posted April 5, 2013 #5 Posted April 5, 2013 Under normal conditions the friction plates may be good for 75K. Depending on how bad, long, and often the clutch was slipped before you replaced the spring can have a huge impact on the overall life of the clutch. It is possible to wear out a set of disks in 1 day with a lot of slipping. Also as mentioned, the choice of oil can have an impact on clutch slippage. When I did my spring upgrade I did the day after the first sign of slip, The only way to tell if the plats have life left is to measure their thickness. New plates are 3mm (.118 inch) thick, the wear limit is 2.8mm (.110 inch) thick. My plates were at .117 thick at 40K miles so I put them back in. If you are in there measuring them I would replace at .113-.114 which is 50% of life. The biggest things that will shorten clutch life are lots of parking lot driving in the friction zone, hard riding, and heavy loads like a big trailer.
kkent66 Posted April 5, 2013 Author #6 Posted April 5, 2013 Should have put this in my original post - I use Mobil 1 racing 4T 10W-40. I do ride 2 up most often but I do not pull a trailer!
bongobobny Posted April 6, 2013 #7 Posted April 6, 2013 There is a heavy duty clutch that Yamaha offers that is a good idea to install when you take everything apart to clean and check. It has more area and you discard that pesky retaining wire when you install. Your choice of oil may be a part of the problem as well. As mentioned, any auto oil with friction modifiers will cause the clutch to slip. Motorcycles have "wet" clutches with oil circulating in them as opposed to a car clutch which is external to the motor and has no oil on it. I would do some research on the oil of choice and see if it contains any friction modifiers. If it does, change it immediately and change it again after a couple hundred miles or less prior to working on the clutch, and drain that oil too before you reassemble. You want to get rid of any traces of friction modifiers. You should use motorcycle oil, or if you want to save some money, diesel engine oil works excellent such as Delo, Rotella, etc.
Flyinfool Posted April 6, 2013 #8 Posted April 6, 2013 The oil you used, Mobil 1 racing 4T 10W-40, is a motorcycle oil that specifically states it is for use with a wet clutch. It "should" be fine. But I have heard of some people having issues with full synthetic motorcycle oils that "should" work. It is possible that either you wore out the clutch back when it was slipping and or it got glazed while it was slipping. Remember there is only .008 inches of thickness between a new and a worn out friction disc. That is only .004 per side, about the thickness of a piece of paper. The only way is to measure each disc. Glazing is not always visible to the eye, a light sanding of all friction and steel surfaces will ensure no glazing. Fortunately it is really easy to service the clutch on these bikes.
bongobobny Posted April 6, 2013 #9 Posted April 6, 2013 Well, there ya go! Jeff did the research for you!!
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now