1joeranger Posted November 12, 2010 #1 Posted November 12, 2010 Time to install a new front tire! Where is the best deal now for Avon Cobra's? Also plan on chaning the fork oil and adjusting the steering Head bearings. Could use some input there! This is the only write up I could find for the procedure: http://www.venturers.org/Tech_Library/index.php?action=article&cat_id=002013&id=349 Thinking about putting a zerk fitting in the steering head yoke area? Any thoughts on that? I know there was a how to write up but cannot find it?! What else should I be doing while I have this all apart? THANKS ALL!!
Kregerdoodle Posted November 12, 2010 #2 Posted November 12, 2010 Try Dennis Kirk for the tire, and Pray that you can get it all back together!! 1joeranger said: Time to install a new front tire! Where is the best deal now for Avon Cobra's? Also plan on chaning the fork oil and adjusting the steering Head bearings. Could use some input there! This is the only write up I could find for the procedure: http://www.venturers.org/Tech_Library/index.php?action=article&cat_id=002013&id=349 Thinking about putting a zerk fitting in the steering head yoke area? Any thoughts on that? I know there was a how to write up but cannot find it?! What else should I be doing while I have this all apart? THANKS ALL!!
Condor Posted November 12, 2010 #3 Posted November 12, 2010 Kregerdoodle said: Try Dennis Kirk for the tire, and Pray that you can get it all back together!! I'd also check with Jake Wilson Free shipping over $100
Kregerdoodle Posted November 12, 2010 #4 Posted November 12, 2010 hhhmmm ya, maybe it was Jake Wilson that I got my E3 from:confused07: man it sucks getting Old..CRS.... Condor said: I'd also check with Jake Wilson Free shipping over $100
etcswjoe Posted November 12, 2010 #5 Posted November 12, 2010 I bought mine from Cycle Gear and It was the cheapest I could find and service was great and they are on sale right now. http://www.cyclegear.com/spgm.cfm?L1=&L2=&L3=&L4=&item=TUC_30-5832_G
1joeranger Posted November 12, 2010 Author #6 Posted November 12, 2010 Thanks All!! Jake Wilson, is in the lead with DennisKirk a nose behind! Cycle Gear is either out of stock or not showing a 150/80R-16. They do show a 150/80HR-17. Not sure what that is but am sure price is not competitive! I have had good service from DennisKirk but wasn't sure who JakeWilson was. So I am assuming JakeWilson.com is legit? Plus they have Dyna Beads!!! Yhea Me!!! Please, really, not trying to start another p****g match here regarding beads!
straycatt Posted November 13, 2010 #7 Posted November 13, 2010 I did the grease zerk mod. Then I pumped in 1 1/2 tubes of grease. I suspect my down tubes will never rust. When I pull the front end down for the fork R&R I'm going to pull the steering head as well and block off the hole that has to be there. I too, tried to get some info on fork oil without much luck. The factory oil is 5wt. I was going to dump in some 10wt to go with the new Racetech 1.0 springs that are going in, but now I'm thinking that may be too thick. Maybe 7wt would be better. I've used both oils in cruisers in the past and liked the ride with both. Anything over 10wt, in my opinion, is too heavy. I tried 15wt in my Spirit and the forks felt like you were riding on a brick.
darthandy Posted November 13, 2010 #8 Posted November 13, 2010 You might also want to check with these guys. http://www.motorcycle-superstore.com/3/31/401/15017/ITEM/Avon-AV71-Cobra-Front-Tire.aspx?WT.ac=SLIsearch
1joeranger Posted November 13, 2010 Author #9 Posted November 13, 2010 Thanks but JakeWilson is selling it for $142.99 with free shipping. Motorcycle Superstore is $165.99 with free shipping. But I have added Superstore to my shopping bookmarks, THanks!!
1joeranger Posted November 13, 2010 Author #10 Posted November 13, 2010 straycatt said: I'm going to pull the steering head as well and block off the hole that has to be there. I read something about this hole awhile back?!??
straycatt Posted November 13, 2010 #11 Posted November 13, 2010 1joeranger said: I read something about this hole awhile back?!?? It was found that some Ventures have a hole in the neck tube left over from fabrication. That hole needs to be welded or closed in some manner, to allow enough grease gun pressure to push grease into and thru the bearings. Otherwise the grease just goes out thru the hole in the tube. I think that even with the hole, my air driven grease gun most likely pushes "some" grease into the bearings, but I'm not 100% confident, as no grease comes out of the bearings. Further, even with the grease trick on the drill bit and tap, when installing the zerk, there is a fairly high risk of metal shavings dropping down into the lower bearing. I think that the grease zerk is a good idea, but it should be done during dis-assembly of the stem.
1joeranger Posted November 13, 2010 Author #12 Posted November 13, 2010 By disassembly I assume I will be doing that during the fork oil change!?
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now