tufftom4 Posted September 2, 2010 Share #1 Posted September 2, 2010 OK now I have the trailer hitch on and the trailer ready to go is there a plug and play trailer connector for the 84 VR like the goldwing or do I have to splice the wires ? I have been searching the tech library but could not find anything. Tom Link to comment Share on other sites More sharing options...
Flyinfool Posted September 2, 2010 Share #2 Posted September 2, 2010 How you need to wire it depends on the type of trailer lighting that you have. Does your trailer have separate brake and turn signals or does it use the same filament for both brake and turn? Link to comment Share on other sites More sharing options...
tufftom4 Posted September 2, 2010 Author Share #3 Posted September 2, 2010 It is a basic 4 pin flat connector that I hooked up to my trucks plug and everything worked fine as to bulbs I have not taken the lights apart to check the filaments. Link to comment Share on other sites More sharing options...
Flyinfool Posted September 2, 2010 Share #4 Posted September 2, 2010 You will need to install a 5 wire to 4 wire converter on the bike. They are available in most any auto parts store. It is best to use a powered one (one that has a separate power and ground wire) so that it does not mess with your flasher. I have never heard of a plug n play for the venture, you will have to tap into the wires under the seat. Link to comment Share on other sites More sharing options...
tufftom4 Posted September 2, 2010 Author Share #5 Posted September 2, 2010 I just found this plug that came with the hitch it has 3 wires in 2 out then a white and brown wire. If this will work let me know I can tear an engine apart and rebuild it but electrical is not my specialty. The pigtail supposedly came from an 83 VR. Link to comment Share on other sites More sharing options...
Flyinfool Posted September 2, 2010 Share #6 Posted September 2, 2010 It is hard to see in the pic but if it is what I think it is it will work. On the end of the box that has 3 wires coming out; The box red goes to the brake wire on the bike is yellow The box green goes to the right turn signal on the bike is dark green The box yellow goes to the left turn signal on the bike is brown. On the end of the box that the 2 wires come out of; The box yellow goes to the flat 4 yellow wire The box green goes to the flat 4 green wire There should then be a brown and a white wire left coming out of the flat 4 connector; The white goes to a good ground on the bike (Preferably the negative battery terminal) The brown goes to the running lights on the bike is blue. There might even be markings on the label of the box to show some of this. Since this in not a powered converter the power to run the trailer lights will come through the electrical system on the bike. Depending on how many lights are on the trailer it is possible to end up blowing fuses on the bike. Test everything with the engine running and the rpm up around 3,000, ( that will give you the full power to the lights) before you take it out on the road for a pull test. You would hate to have to sneak home with no brake lights or something. Link to comment Share on other sites More sharing options...
tufftom4 Posted September 2, 2010 Author Share #7 Posted September 2, 2010 OK thanks but where do I spice the wires? is it under the seat or somewhere else? I just bought a new high output rectifier since I was having problems with my original. Link to comment Share on other sites More sharing options...
Flyinfool Posted September 2, 2010 Share #8 Posted September 2, 2010 The wire harness to tap into should be under the seat on the left side. Link to comment Share on other sites More sharing options...
tufftom4 Posted September 3, 2010 Author Share #9 Posted September 3, 2010 Thank you I will let you know how bad I mess it up. Link to comment Share on other sites More sharing options...
Flyinfool Posted September 3, 2010 Share #10 Posted September 3, 2010 Link to comment Share on other sites More sharing options...
tufftom4 Posted September 3, 2010 Author Share #11 Posted September 3, 2010 One more thing the trailer has regular bulb lights would it be better to buy led lights to put on ? Link to comment Share on other sites More sharing options...
Flyinfool Posted September 3, 2010 Share #12 Posted September 3, 2010 Going to LEDs on the trailer will help to reduce the current draw a lot. With the high current draw of the standard bulbs the flasher may not work correctly. Link to comment Share on other sites More sharing options...
tufftom4 Posted September 8, 2010 Author Share #13 Posted September 8, 2010 OK I did as you said wired up the lights put a new connector on the trailer but did not go to led just used the ones that came with the trailer, all the lights work great no blown fuses and the little box fit perfectly with the air system. I bought an aftermarket high output rectifier but I do not have the tools to fab up a bracket, anyone have any ideas to make it easy ? THANK YOU FOR ALL THE HELP. Tom Link to comment Share on other sites More sharing options...
Flyinfool Posted September 8, 2010 Share #14 Posted September 8, 2010 Glad the wiring worked out and you are ready to roll. Just make sure that you have some spare fuses with you at all times, just in case. You should be good, but I always err on the side of caution. You may want to start a new thread for the H.O. R/R. I can not help you with that one, mine is still stock. Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now