mattevans Posted March 9, 2009 Share #1 Posted March 9, 2009 HAD A NICE WEEKEND AND DID SOME RIDING ON SATURDAY. ABOUT 30 MILES INTO THE RIDE I LOOK DOWN AND MY TEMP GUAGE HAD STOPPED WORKING. FAN COMES ON AS NORMAL, NO BLOWN FUSES. I DONT KNOW WHERE THE TEMP SENSOR IS LOCATED NOT SURE IF THIS WOULD EVEN BE THE PROBLEM. HAS ANYONE ENCOUNTERED THIS, GOT ME STUMPED COULD USE SOME HELP WITH THIS ONE. Link to comment Share on other sites More sharing options...
5bikes Posted March 9, 2009 Share #2 Posted March 9, 2009 Behind the chrome right side grill just behind the radiator. Two philips screws hold it on. Usually the electrical connections are loose or need cleaning and tightening. 2 sets of connectors. Then check connectors on the back of the gauges. Check all grounds there too. Link to comment Share on other sites More sharing options...
BradT Posted March 9, 2009 Share #3 Posted March 9, 2009 I believe (not sure this is the right wire) but along the upper frame rail on the right side of the bike there is a connector that just needs to be pinched tight. You have to remove the lower fairing on the right side and it is a single wire. Cant remember the colour. Brad Link to comment Share on other sites More sharing options...
Rocket Posted March 9, 2009 Share #4 Posted March 9, 2009 I believe (not sure this is the right wire) but along the upper frame rail on the right side of the bike there is a connector that just needs to be pinched tight. You have to remove the lower fairing on the right side and it is a single wire. Cant remember the colour. Brad The bullet connector is the one to tighten (temp sending unit), as the spade connector is the ground for the fan motor........ Link to comment Share on other sites More sharing options...
mattevans Posted March 9, 2009 Author Share #5 Posted March 9, 2009 behind the chrome right side grill just behind the radiator. Two philips screws hold it on. Usually the electrical connections are loose or need cleaning and tightening. 2 sets of connectors. Then check connectors on the back of the gauges. Check all grounds there too. i think i saw these it looked like there were two sensors side by side not sure which one is which they are conected to what looks like the top radiator hose. Are both of these sensors the same or do they each have a seperate purpose. Link to comment Share on other sites More sharing options...
Rocket Posted March 9, 2009 Share #6 Posted March 9, 2009 i think i saw these it looked like there were two sensors side by side not sure which one is which they are conected to what looks like the top radiator hose. Are both of these sensors the same or do they each have a seperate purpose. Read my previous post....... Link to comment Share on other sites More sharing options...
mattevans Posted March 9, 2009 Author Share #7 Posted March 9, 2009 Read my previous post....... FOUND IT!! THANKS..... IS THERE A WAY TO CHECK TO SEE IF THE SENSOR IS WORKING PROPERLY, MAYBE WITH A METER. Link to comment Share on other sites More sharing options...
bobcat Posted March 9, 2009 Share #8 Posted March 9, 2009 Matt....I had the same problem....I was advised the same as you to clean and tighten the wire connector and bullet end of the sensor...I did the same for the fan sensor for good measure while I was in there.....My temp guage has been working fine ever since.... Link to comment Share on other sites More sharing options...
Squeeze Posted March 9, 2009 Share #9 Posted March 9, 2009 FOUND IT!! THANKS..... IS THERE A WAY TO CHECK TO SEE IF THE SENSOR IS WORKING PROPERLY, MAYBE WITH A METER. No need yelling at us. Typing in CAPS is consider yelling ... Yes, you can check with the Shop Manual, there are the Specs of the Sensor stated. Link to comment Share on other sites More sharing options...
mattevans Posted March 9, 2009 Author Share #10 Posted March 9, 2009 No need yelling at us. Typing in CAPS is consider yelling ... Yes, you can check with the Shop Manual, there are the Specs of the Sensor stated. Sorry, i was'nt yelling im just computer stupid. Link to comment Share on other sites More sharing options...
Venturous Randy Posted March 9, 2009 Share #11 Posted March 9, 2009 Sorry, i was'nt yelling im just computer stupid. Well, we now know that you have even more in common with most of us. RandyA Link to comment Share on other sites More sharing options...
Squeeze Posted March 9, 2009 Share #12 Posted March 9, 2009 Not a Problem, I Kind of guessed it anyway. But somewhere else on Forum's you could have been suspended for 2 Days or so ... Link to comment Share on other sites More sharing options...
mattevans Posted March 10, 2009 Author Share #13 Posted March 10, 2009 Matt....I had the same problem....I was advised the same as you to clean and tighten the wire connector and bullet end of the sensor...I did the same for the fan sensor for good measure while I was in there.....My temp guage has been working fine ever since.... Thanks bobcat you were right, it was a bad conection at the bullet conector. I cleaned it and tightened it up now it works great. Link to comment Share on other sites More sharing options...
bobcat Posted March 10, 2009 Share #14 Posted March 10, 2009 Right on Matt.....Thanks for the followup...Don't ya just love it when a fix doesn't cost anything? I know I do.. Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now